'97+ TJ Wrangler Dana 44

____The Streetrod Manufacturing Co. Inc.____

'97 & Later TJ Wrangler Dana 44 rear disc brake kit includes: brackets, bolts, new 11 1/4" vented rotors, spacer plates and studs. (You will also need to purchase Calipers and Lines to complete the installation. Options of Calipers with or without a parking brake and rubber or stainless hoses are available in Additional Parts shown below) Link for info on ABS Part Number 2563-44 $279.95pair Fits 15 Inch and Larger Wheels

Brake Kit for Warn Full Float Hubs. (We do not have the hubs) Link for info on ABS Part Number 2563-44W $279.95 pair Fits 15 Inch and Larger Wheels

Brake Kit for Warn Full Float Hubs with 5 X 5 1/2 wheel bolt pattern. (We do not have the hubs) Link for info on ABS Part Number 2551W $289.95 pair Fits 15 Inch and Larger Wheels

Link for Info on Calipers, Flex Lines Etc.

Additional Parts (Needed to complete installation)

Part No. DS Dimpled & Slotted Rotors additional $79.95 pair Slotted Rotor Photo

Part No. 3100 New (Not Rebuilt) Calipers without parking brakes $120.00pair

Part No. 3110 New (Not Rebuilt) Calipers with parking brakes $300.00 pair

Part No. 3111 Short Cable Extensions $20.00pair

Part No. 3700 Rubber hose 9 1/2" $50.00pair

-OR-

Part No. 3702-8 Braided Stainless hose 8" $50.00pair

Assembly Instructions

Rear Disc Brake Conversion

(C-Clip Style)

Parts List

(2) New Vented Rotors

(2) 2 Piece Brackets

(8) 5/16" Spacers

(4) 3/16" Spacers

(8) 3/8 – 24 X 1 1/2 Grade 8 Bolts

(8) 3/8 – 24 X 2 Grade 8 Bolts

(16) 3/8 Flat Washers

(16) 3/8 Grade 8 Lock Washers

(16) 3/8 - 24 Grade 8 Nuts

Installation Instructions

Remove the axles to take the backing plates off.
Install the base brackets with the caliper up and towards the rear. Use the 1½" bolts, flat washers, lock washers, and nuts. The bracket can go in a 45-degree or 90-degree position and if you flip the bracket over slightly different positions are available. The rear parking brake calipers have their bleed screw in the 90-degree position and the front calipers have the bleed screw in the 45-degree position. Bolt the top bracket to the base with the spacers between. (The Bracket is spaced to the inside of the vehicle away from the rotor. (50 ft. lbs. dry 35 ft. lbs. Lubed)
Install new seals, and then the axles.
Install the rotors, making sure the surfaces that meet are clean with no projections that would make the rotors wobble, and hold in place with a couple of wheel nuts.
Rotate the rotors and check for wobble, if there is any, check for interference in the mating surfaces, if not then the axle and rotor bolted together should be faced to true up. Mark the position that it is bolted to the axle so that it can be reinstalled the same way if the rotors are ever removed.
Install the calipers so that the bleed screw is facing up, if it is facing down use the other caliper. Make sure the projections on the bottom of the calipers don’t touch the bracket.
Use a flexible brake line to each caliper as they move with pad wear and when the brakes are applied.
Bleed the brakes and try out. If the back wheels skid before the fronts you should install an adjustable proportioning valve to reduce the pressure to the rear brakes (follow gravity bleeding instructions in troubleshooting sheet especially for rear calipers).

For ordering and information call 1-303-688-6882. Send mail to TSM Staff with questions or comments about this web site. WE DO NOT HAVE A SECURE E-MAIL SITE. You can fax, phone, or mail your order to submit new credit card information. Thank You.

ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.